THought if i posted here someone might have information pertaining to doing such a thing.Īlso thought maybe someone could tell me if this CCC and MCC should work together or what?Īnd if there was a good recommended place where i can just get the pinouts of the MCC i have, if it will indeed work with the CCC.
ROWE AMI CD JUKEBOX MAKE LIGHTS BLINK SOFTWARE
I am not to familiar with jukeboxes right now, still learning.īut at one place there was mention of talking to the CCC via rs232 which i assumed meant using the pins on the CCC but am unfamiliar to know if i need special software or if i can just use like hyperterminal. Hope i am using the correct terms here.Īnd if you dont mind my asking what is difference between CD100e and CDM12? But after like a min or so the system error light on the CCC comes back on and stays on. So i am thinking the issue is either the MCC or some mechanizm attached to the MCC being as no other lights light on it. The 5 v light lights up on the MCC but no other lights light on the MCC, so it does not home does not load does not play. The 5 v light light up on the CCC the system error light comes on for a second or so then blinks and goes off, the rowelink light is flashing. When i turn the juke on the power lights on power supply light up and the voltages are as they should be.
![rowe ami cd jukebox make lights blink rowe ami cd jukebox make lights blink](https://www.picclickimg.com/d/l400/pict/174840430762_/Rowe-AMI-jukebox-lamp-control-part-no-40869702.jpg)
Ok the problem i know has something to do with the MCC. Is it possible to connect to this via a rs232 port on a computer to diagnose things using like hyperterminal or do you need special rowe software to communicate with this port? Now the final question I was looking at the prints for the CCC there is a max232 chip near the one plug and the pinouts are ground, rx, tx, cts, and rts. Of course a schematic would be good as well but figure first start with the externals and trace the various IO to the MCC. I am looking for the pinouts so i know what the various plugs and pins do. If it is suppose to be the part number i have then i can only assume that either i have an older book or a faulty book.Ĭan someone recommend where i can get a proper book or at least the section pertaining to the MCC.
ROWE AMI CD JUKEBOX MAKE LIGHTS BLINK MANUAL
I am certain there are others out there that have this jukebox so if you happen to have a manual could you tell me, which is the proper part number that i should have for my MCC? So now that i have that out of the way here is my list of questions.
![rowe ami cd jukebox make lights blink rowe ami cd jukebox make lights blink](https://www.picclickimg.com/d/l400/pict/333829787124_/ROWE-JUKEBOX-part-COMPUTER-CONTROL-MODULE-6-50439-01.jpg)
The number i have on my MCC box is 61086201 but the number in the manual i purchased is 61030603 so when it comes to diagnosing the MCC i can not do it. When it comes to the power board, it is laid out and part number exactly as listed, when it comes to the CCC the part numbers match the number is 40832220, However the one that does not match is the MCC. And for the most part the manual is absolutlely correct. I went to ebay and purchased what is said to be a manual for it. I recently acquired a CD100-E, it does not work, so i am working on it. So i hope i dont offend by asking the following bits of information.
![rowe ami cd jukebox make lights blink rowe ami cd jukebox make lights blink](https://www.picclickimg.com/d/l400/pict/163562791053_/Rowe-Ami-Cd-Jukebox-Cd100F-Pair-Of-Lower-Light.jpg)
Ok i am new here so this might have been covered before but for the life of me i can not seem to locate.